Maytag MMC5000BDB Installation Manual de usuario descargar pdf

INSTALLATION

INSTRUCTIONS

Microwave Oven Built-In Kit

Model MMA27 And MMA30

With Use On Model MMC 5000 Microwave Oven.

OBSERVE ALL GOVERNING CODES AND ORDINANCES.

STEP 1: Electrical Requirements

A. A 120-Volt, 60 Hz, AC, 15 ampere, fused electrical supply is required

(time-delay fuse or circuit breaker is recommended). However, if your

homehas acircuit wiredand fused for20amperes, thisis preferred.If

youare installinganew circuit, onewired andfusedfor20amperesis

recommended. It is also recommended that a separate circuit serving

only this appliance be provided. Do not use an extension cord.

B. ELECTRICAL CONNECTION: ELECTRICAL GROUND IS RE-

QUIRED ON THIS APPLIANCE. DO NOT UNDER ANY CIR-

CUMSTANCES, REMOVE THE POWER SUPPLY CORD GROUND

PRONG.

FIGURE 1

Required Grounding Method

3-Prong Grounding Plug

Power Supply Cord

Properly Polarized 3-Hole

Grounding Type Wall Receptacle

Foryourpersonalsafety,thisappliancemustbeproperlygroundedand

polarized. Thisapplianceisequipped with a powersupply cordhaving

a3-pr onggroundingplug.Tominimizepossibleshockhazard,thecord

must be plugged into a mating 3-hole grounding type wall receptacle,

groundedinaccordancewiththeNationalElectricalCode, localcodes

and ordinances. If a mating wall receptacle is not available, it is the

personal responsibility and obligation of the customer to have a

properly grounded and polarized 3-hole wall receptacle installed by a

qualified electrician. (See figure 1).

NOTE: A 27² minimum wide cabinet must be provided to install T rim Kit

MMA27.

NOTE: A 30² minimum wide cabinet must be provided to install T rim Kit

MMA30.

STEP 2: Cabinet Opening

Theopeningshouldbeperdimensionsdescribedbelow.Allcornersshould

besquare.Theflooroftheopeningmustbeplywoodandmustbeleveland

capable of supporting 80 lbs.

FIGURE 2

MODEL

MMA27

MMA30

DIM. “A”

25-1/2²

28-3/16²

DIM. “B”

2-3/4²

4-1/16²

STEP 3: Assembly Of Intake Hood (See Figure 3)

A. Remove screw A.

B. Place rear intake hood against rear of microwave.

C. Align hole in rear intake hood and microwave unit, reinstall screw

removedinstepA.

Note: Route microwave cord through cable relief hole.

D. Placetopintakehoodsoholeatfrontalignswithholeinmicrowaveunit

front.

E. Install 2² shoulder screw to attach top intake to microwave unit.

F. Install rear screw to attach top intake hood to rear intake.

FIGURE 3

WARNING

The weight of the microwave may exceed your lifting

ability. We recommend assistance.

8101P346-60

(11-99-00)

1 2

Indice de contenidos

Pagina 1 - Model MMA27 And MMA30

INSTALLATIONINSTRUCTIONSMicrowave Oven Built-In KitModel MMA27 And MMA30With Use On Model MMC 5000 Microwave Oven.OBSERVE ALL GOVERNING CODES AND ORDI

Pagina 2 - IMPORTANT

STE P 4: Assembly Of Exhaust Hood (See Figure 3)A. Remove screw B.B. Place side exhaust hood against the rear and side of microwave unit.C. Align hole

Modelos relacionados MMC5000BDQ Installation | MMC5000BDW Installation |

Comentarios a estos manuales

Sin comentarios

Maytag MMC5000BDB Installation Manual de usuario

Busca en linea o descarga Manual de usuario para Microondas Maytag MMC5000BDB Installation. Maytag MMC5000BDB Installation User Manual Manual de usuario

Indice de contenidos

Modelos relacionados MMC5000BDQ Installation | MMC5000BDW Installation |

Comentarios a estos manuales

Relacionado con productos y manuales para Microondas Maytag MMC5000BDB Installation